Honeywell Y8185 Manuel d'utilisateur télécharger pdf

Honeywell

180850/06828,C, 18185/06828,C,L, Y8185, Y8024,

HEATING AND HEATING/COOLING

NEW CONSTRUCTION THERMOSTATS AND SUBBASES—

INSTALLATION INSTRUCTIONS

1 PREPARATION^

----------------------------------

D Check thermostat and subbase (it used) suitability

for the heating or heating/cooling system. Refer to

Tablet.

□ Assemble tools required: flat blade screwdriver,

hand or power drill with 3/16 in. drill bit, wire cutter/

stripper or sharp knife, bubbie level or plumb bob and

line.

LZ] If subbase or wallplate is mounted on a vertical

outlet box, order the optional 193121A Cover Plate

Assembly (inoludes cover plate, adapter ring,

screws).

and

□

Ensure power is off to the heating or heating/

cooling system at the main fuse panei. Most buildings

have a separate switch box or circuit breaker for dis

connecting power to the heating and cooling (if appli

cable) equipment.

THIS THERMOSTAT is compatible with virtually all heat

ing or heating/cooling systems. See Table 1 for addi

tional thermostat compatibility information.

TABLE 1—THERMOSTAT AND SYSTEM COMPATIBILITY

TYPE OF HEATING SYSTEM TO BE CONTROLLED

CONDiTIONS/COMPATIBILITY

Electric (line voltage)—typical baseboard and radiant

• The R8239D1015 Isolating Relay or R841 Silent

Switching Center must be installed in the thermostat

control circuit.^

Electric Furnace—forced air • Compatible, Ensure correct subbase identity selected

for fan control.

Gas—Direct Spark Ignition (DSl), Intermittent Pilot (IP),

and Standing Pilot (SP)

• Compatibia Ensure that the 24 V control transformer

common is accessible for connection to thermostat

cable conductor and power to transformer is not reg

ularly interrupted by high temperature or limit

operation.

Heat Pump • Compatible, Ensure correct subbase identity selected

for fan control and changeover control (0 terminal for

cool and B terminal for heat),

• If system with first stage heat pump and gas or oil

second stage heat, use conventional recovery

models.

• If system with first stage.heat pump and electric

second stage heat, use ramp recovery model.

Hot Water Zone

• Honeywell 2-wire valves are compatible.

• Some non-Honeywell 2-wire valves will require a'

R8239D1015 Isolating Relay In the thermostat control

circuit.^

• Some 3-wire valves will require an R8239A1052 Iso

lating Relay in the thermostat control circuib^.b

Oil

• Ensure that the 24 V control transformer common is

accessible for connection to thermostat cable con

ductor and power to transformer is not regularly

interrupted by high temperature, purge cycle, or limit

operation.

• If the control transformer common is not accessible,

a separate transformer and TRADELINE wallplate or

subbase with two C-C clock terminals will be

required.

Vent Damper • Honeywell damper motors are compatible,

• Some non-Honeyweli damper motors will require an

RS239D1015 Isolating Relay in the thermostat control

circuit.3 Check control amperage requirement.

Warm Air Zone

• Most are compatible.

Hf thermostat is not compatible with the system being controlled, the system will not operate. No hazard exists. The

thermostat will not be damaged unless it is used to directly control a line voitage system, A Honeywell R841 or

R8239D1015 Isolating Relay must be added to the thermostat control circuit for proper system operation,

^Consult manufacturer for installation requirements.

C.H.

Rev, 7-88*

Form Number 69-0258—2

®Honeywell inc. 1988

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Honeywell

Honeywell180850/06828,C, 18185/06828,C,L, Y8185, Y8024, HEATING AND HEATING/COOLING NEW CONSTRUCTION THERMOSTATS AND SUBBASES— INSTALLATION INSTRUCTIO

Page 2 - 3 UNPACK THERMOSTAT

Locate thermostat about 5 ft. [1.5 m] above the floor in an area with good air circulation at average temperature. Do not mount the ther

Page 3 - 5 WIRE WALLPLATE OR SUBBASE

Fig. 3—Leveling methods for wallplate or subbase.5 WIRE WALLPLATE OR SUBBASEFollow the Instructions provided by the heating or heating/coollng

Page 4 - TYPICAL GAS VALVE

D Note the tabs on the top inside edge of the thermostat base. These fit the slots molded into the top of the wailplate or subba

Page 5 - Fig. 9—Attach cover

8 SET TIMER -----------------------------------------iZH Adjust the timer by moving the knob in clockwise direction. Do NOT reverse the knob.□ When t

Page 6 - CAUTIONS

12 CHECK OUT THERMOSTAT OPERATION'□CAUTIONSDo NOT check operation by shorting across terminais of relay or valve coil; this will

Page 7 - THERMOSTAT

AFig. 12—Hookup showing a typical heating/cooling control system.THERMOSTATAeFig. 13— Hookup showing a typical electric heating/mechanical cooling con

Page 8

Af/1\ POWER SUPPLY, PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED,/z\ CONNECT VALVE TO TERMINAL O FOR POWER ON COOLING OR TO TERMINAL

Modèles reliés Q682B | Y8024 |

Commentaires sur ces manuels

Pas de commentaire

Honeywell Y8185 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Panneau de contrôle Honeywell Y8185. Honeywell Y8185 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés Q682B | Y8024 |

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Honeywell Y8185