Honeywell D Manuel d'utilisateur télécharger pdf

X-XX UL

INSTALLATION INSTRUCTIONS

®U.S. Registered Trademark

T8112C,D Electronic

Programmable Thermostats

APPLICATION

The T8112C,D thermostats provide electronic

programmable control for 24 to 30 Vac heating and

cooling systems.

RECYCLING NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do

not

place your old

control in the trash.

Contact your local waste management authority

for instructions regarding recycling and the proper

disposal of the old thermostat.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could cause a hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

1. Disconnect power supply to prevent electrical

shock or equipment damage.

2. After wiring is complete, push excess wire

back into the hole and plug hole with

nonhardening caulk, putty or insulation to

prevent drafts from affecting thermostat

operation.

Location

Install the thermostat about 5 ft. (1.5m) above the floor in

an area with good air circulation at average temperature.

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Mounting Plate Installation

Position mounting plate on the wall. Use a level to make

sure mounting plate is level. Use a pencil to mark the two

mounting holes. See Fig. 1.

WALL

WIRES THROUGH

WALL OPENING

WALL ANCHORS (2)

MOUNTING

PLATE

MOUNTING

SCREWS (2)

M1718

69-0917-2

Fig. 1. Mounting plate installation.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Programmable Thermostats

Page 2 - Wiring Thermostat

69-0917—22T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATS1. Remove mounting plate from the wall, and drill3/16 inch holes in wall (if drywall) as marked.

Page 3 - W Y G

69-0917—23T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATSRRcW Y GB DA C2-WIRE HEAT-ONLY (JUMPER INTACT)M1709BL1(HOT

Page 4 - ENGAGE TABS AT TOP OF

69-0917—24T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATSM1712AJUMPER (FACTORY-INSTALLED) REMOVE IF 5-WIRE SYSTEMINSERTSTRAIGHT UNDER SCREW HEAD5/16 in.

Page 5 - SETTINGS

69-0917—25T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATSAs the batteries are running low, a “bAt Lo” indicator flashfor one to two months before batteri

Page 6 - CHECKOUT

69-0917—26T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATSCHECKOUTHeatingDo not check heating system operation by jumperingthermostat terminals at the pri

Page 7 - TROUBLESHOOTING GUIDE

69-0917—27T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATSTROUBLESHOOTING GUIDENOTICEThis equipment is a Class B digital apparatus, which complies with Ca

Page 8 - 69-0917—2

69-0917—28T8112C,D ELECTRONIC PROGRAMMABLE THERMOSTATSHome and Building ControlHoneywell Limited-Honeywell Limitée155 Gordon Baker RoadNorth York, Ont

Commentaires sur ces manuels

Pas de commentaire

Honeywell D Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Thermostats Honeywell D. Honeywell D User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Thermostats Honeywell D